Kitchen

I know, sailors call it a galley. Mine's a kitchen.

The underwater sections of the hull all read dry with my moisture meter, except for an area below the kitchen floor. The kitchen floor consisted of foam and a layer of glass. I peeled back the glass:

You can see staining from water. I removed all the foam. The original builder of the boat fitted a floor this way. It's a bad idea. Bilge areas need to be dry and ventilated, or moisture builds up in the glass. Nothing is entirely waterproof - even epoxy coated hulls. Some water always passes through into the glass. If the water can evaporate from the inside as fast as it penetrates from the outside, it can't build up to a level that will allow osmosis to begin. Having water on the inside of a hull as well as the outside makes osmosis inevitable.

Anyway, it was a simple matter to remove the foam, and lay down a more traditional plywood floor. I first epoxied in some supports which greatly strengthen the hull right over the keel shoe I fitted, so that was a nice benefit of the new arrangement. And I think the finished floor looks a lot nicer than the old fibreglass one:

Note the foot pump I fitted by the step, to supply water to the sink. There used to be a hand pump, but washing your hands when one of them is occupied pumping water is just silly. And the pump was flimsy too. This Whale footpump is much more robust, and allows for a great deal of control when hand washing - this is important to me. The more frugal I can be with water, the less I need to carry. Less weight, more speed, or the ability to carry other essentials.

So, I got carried away. New worktops - normal domestic worktops which I modified for a multihull - ie, lightening them as much as possible by using a router to remove much of the chipboard under the surface, and then sealing the chipboard and all edges with epoxy resin.

New hob too. Cookers for boats used to be very expensive. Gas is heavier than air, and any gas leaking ends up in the bilge, waiting to blow a boat apart. So marine cookers need to be fitted with flame failure devices that turn off the gas if the flame goes out. That has now become the required way to supply domestic cookers too, so a stainless domestic cooker is just as good as an expensive 'marine' cooker from a chandler.

I'll make a stainless fiddle that hinged up against the bulkhead that will keep pans in place when the boat is sailing fast through bumpy water. Usually, fiddles aren't needed in a multihull, but I did once lose my chip pan when I hit a rough patch in the Gibraltar Straits. That was messy. So fiddles will be made and installed.

Only two burners on the hob, but I figured that with with a new grill and oven too, we'd manage OK. The little door beside the oven used to be a fridge. Silly place for a fridge, next to the oven. Not sure if a fridge is such a good idea for a cruising boat anyway. It's a big power draw which needs feeding with more batteries and solar panels - more expense, weight, and things to go wrong. I've got by just fine with several summers in the Mediterranean without a fridge, and never missed it. There are other ways to keep things fresh (wrap cheese in cloth, not plastic, keep cabbages and lettuces upside down in nets, allow plenty of air to circulate round fruit and vegetables, and sprout mung beans or alfalfa for salads and stir fries).

Cupboards. 10 of them altogether, 2 drawers, and a great big space under the cooker than could easily take a couple of sacks of potatoes. That space under the cooker used to house a waste water tank, which needed to be pumped out. I got rid of the tank, the pump and two underwater through hull fittings. There are a couple of places that don't allow disposal of washing up water into the sea. I won't go to those places.

Marine taps are expensive too, so I bent a bit of copper pipe. I think it looks quite nice. Well, water comes out of the end and without leaking anywhere else, when you pump the foot pump. And the tap can be turned away from the sink to over the step, when you need to fill a large container.

Just under the tap is a little box with a green light on. The light turns red and the box screams when it detects gas. Handy, just in case a flame failure device on the cooker fails.

This gas detector works very well, but I'm not sure what gas it tests for. It surprised me one day as I was working on the kitchen floor. I was down there on my knees, and did a little fart, and then this piercing alarm went off. I ran around for a little while before I realised what the alarm was, and why it had gone off. :)

That's a big kitchen for a 30' boat. But on a long voyage, there often isn't much to do except read and cook. So the kitchen to me is very important, much as I like reading.

Nigel Irens' influence on my boat

You know who Nigel Irens is don't you? Famous boat designer?

Well, he's been building a nice motor launch in the same shed as me. He's just finished and launched it, and donated the remaining bits of wood to us catamaran fixer-uppers, including some bits of nice teak faced poplar.

So I made some new drawers for my galley.

Thanks Nigel! Nice to have a bit of Irens input on my boat!

Fixing 750 holes in my boat.

The curved foam sandwich anchor lockers in front of my main beam were poorly made. I guess the foam and the outer glass skin weren't attached as well as they ought to have been. Anyway, my moisture meter showed water in there, and after drilling a few test holes, I got wet. So I drilled holes throughout the area that read as damp, 30mm or so apart. I then rinsed the foam by squirting water in turn into the holes, and vaccuuming it back out again. I did this many times!

Eventually, I judged it rinsed enough and let it dry out for several months. Readings with the moisture meter dropped into the green zone. It was time to fill the gaps between the foam and the glass by injecting epoxy.

I've injected epoxy before, and it can be pretty messy. Injecting with a syringe can get the epoxy squirted into quite a large area, but as soon as you take the syringe away it comes out again pretty quick. The easiest part of my problem area was vertical, and some of it even tougher, beyond vertical. I was keen to find a way to plug the holes using something that wouldn't be washed away with epoxy. Masking tape is just washed off by epoxy, and so is gaffer tape. Previously, I've found making a circle of builder's filling mastic round the hole, and then putting tape over it makes a leak-proof seal. But I had a lot of holes, so this method wasn't practical.

One day, I noticed a price tag stuck to a filling knife I was using to work with epoxy. The tag remained well stuck  So I bought a roll of 250 price tags. And then cut the roll into three, giving me 750.

I used nearly all of them, but fortunately, I had some assistance. The price tags worked perfectly. They even stuck to the fibreglass that was already wet with epoxy.

Fitting new windows

My windows used to leak. And the Perspex was crazed and foggy.

The old windows were held in place with some sort of mastic and bolts spaced about 3 inches apart. The leaks were mostly around the bolts, though the worst window leaked most because, as I discovered when I removed it, the plastic film that protects Perspex when it was new had been left in place.

I wanted to get rid of all the bolt holes. As well as being prone to leaking, they provide stress points in the Perspex. Around many of the bolt holes, there were clear signs of cracking in the old windows.

I have just finished fitting my new windows for the second time. The first time, I used the instructions I found here. The windows leaked within days. The paint I used was paint used for car exhaust pipes, as suggested in the article. But the article is Australian, and I am in the UK, so maybe the paint here is different. Anyway, it didn't work. The windows failed in the join between the paint and the mastic/tape. On removing the windows, I was disappointed with the performance of the tape. I'd expected it to be easy to remove from the Perspex, as the paint hadn't provided a good surface for it to adhere to, but it also easily came away from the hull. I don't know why that is. That 3M double-sided tape is recommended all over the net. All I can say is that it didn't work for me.

The second time around, I've used Sabatack 780, and their very expensive UV protective primer (£33 for a tiny bottle - but it was enough for my 15 windows).

It's important to use spacers between the window and the hull to get the right thickness of mastic - too much is both expensive and ugly. Too little doesn't allow enough flexibility between the Perspex and the hull. Perspex expands and contracts with temperature change much more than fibreglass, so some flexibility in the connection is crucial. I used little squares of hardboard glued to the hull (3.5 mm):

It's important to place the windows correctly first time on the hull after you've applied the gloop - trying to adjust the position once the gloop has made contact with the hull makes a mess. I did a dry run for each window, and drew a pencil line round the windows. I then glued some bits of wood in place to help guide the window to the correct position. I used plywood, but it would have been better t use some thicker wood so that the windows is guided into place from a greater distance from the hull. I wanted to glue the wood to the hull in such a way as to allow me to remove it easily without damage. Here's the trick to that:

Stick some masking tape to the hull where you want the wood to go, then use 5 minute polyurethane wood glue to attach the glue to the tape. The wood blocks can be easily removed with a chisel without damaging the hull, but the wood is stuck down well enough for locating the window, and can even be used as a base for clamping the window down. Here's a window that wasn't quite bent enough - I just clamped it down onto the spacers until the mastic had set:

The Sabatack was easy to clean up with a chisel the next day. It seems to go hard quite slowly, though you are supposed to put the window in place within 8 minutes of applying the glue.

It all seems to have worked well. I got 15 windows glued in and cleaned up in two days. That feels like progress at last. How waterproof and strong they turn out to be, only time will tell.

Six days later....

Only after I'd stuck in all the windows did it occur to me to test this system. Oh well, better late than never. I cleaned some scrap Perspex with isopropyl alcohol, applied the primer, left it to dry for 10 minutes, then glued on some scrap fibreglass using a narrow bead - as I'd done for the windows. After six days, I tore the pieces apart:

That's 10 mm Perspex under the crow bar, and 15mm foam sandwich on top. It took a lot of effort to break it apart! Now I'm certain the windows are securely installed. I checked where the glue failed - I'd expected the primer to tear away from the perspex, or the glue to come away from the primer. But those interfaces held! The glue tore away down the middle of the bead - and here it was still tacky. So I guess, even after six days, and having reached this fantastic strength, the glue would have become even stronger if I'd left it longer.

:)

Update: 2 and a half years later, mostly in the tropics, the windows are still fine. No leaks at all, no sign of any loosening.

Water - catching rain

I've fitted a water catching system to the coachroof.

I have a friend who sailed round the world using only the rain water that fell on his coachroof - and his coachroof is quite a bit smaller than mine.

But why bother? I have 2 x 150 litre tanks. On a recent trip from the Azores to the UK that took eight days, I used just 25 litres of water, and that included using fresh water for cooking and to wash up. So I guess I could eke out my water for 300/25 x 8 = 96 days. However washing was minimal (I was sailing alone), and I did no laundry.

It would be nice to be able to take a shower. And to wash clothes in fresh water. And to rinse the salt out of clothes that become salty (otherwise they never properly dry).

I could do all those things using rain water. And to replenish my drinking water, I could pour the collected rain water through a filter - they make them so fine these days that they filter out even things as small as viruses. Rain water fed directly to the main tanks would be silly - I have no desire to drink water contaminated with seagull poop.

It seems a no-brainer. The alternative is to carry lots of water (300 kgs for full tanks), and be reliant on shore supplies (which often means using a marina, which I intend to avoid as much as possible). Or to install a water maker. That's expensive, to buy and to maintain. And it needs a lot of power, so it needs lots of solar panels or a generator. To rely on the sun or a generator, and a water maker for a supply of water seems less secure than relying on rain.

It seemed a good opportunity to fit the catching system - I've just removed all the car body filler that had been used to fair the boat, and refilled using epoxy filler (car body filler absorbs water - a pin-prick through the paint results in filler absorbing water and eventually causing blister and then more holes in the paint). After fairing in the coachroof, I used a hot glue gun to attach to 15mm plastic plumbing pipe to the bottom of the coachroof. I then used epoxy filler to fill the space under the pipe, and create a gutter. I used release mould on the pipe - but this wasn't necessary. Epoxy doesn't stick to the pipe anyway.

After pulling the pipe away, I glassed over the filler underneath and on top.

The red and blue colour in the photo is epoxy filler - I added red or blue builder chalk to each mix of filler, to make it easier to see what I was doing when it came to sanding t smooth. (Currently the boat looks very badly bruised!).

I left a gap where I want the water to run out when I am not collecting, and drilled a hole through the deck just uphill from the gap. In the deck hole, I epoxied a long plastic pipe insert (standard plumbing part, 40p!) which is the right size for push-fit plumbing fittings. The pipe comes out behind a bulkhead in the kitchen, so it will be easy to attach some plastic pipe to the inlet leading to a tap which I'll set at the height of my water containers.

Update: I'm anchored in Turks and Caicos, and water costs $2/gallon. There are no taps anywhere but in marinas, which are $50 a night. We're living on rainwater that arrives in occasional squalls. Crap from seagulls seems an English problem, or northern European anyway. I can't remember how far south we had to go before bird shit wasn't a problem. Anyway, south of Portugal and in all of the Caribbean, all we need to do is let the first water wash dust  and salt off the roof, then collect the rest. It is a lot of work though, carrying the containers up to the deck to syphon them into the tanks. Despite my initial reservations, I think it would be much better to plumb the rain catching system directly to the tanks, with a diverter tap for discarding the first water.

more problems with the front beam

Stripping the old fittings from the aluminium beam at the front of the boat, I was disconcerted by the sight of how much corrosion there was:

And strangely, there was dampness underneath, despite the boat having been under cover for a couple of months.

I drilled a hole in the bottom, and 3 litres of water poured out, which tasted salty.

I drilled a couple of holes in the top, the same distance apart as the camera lens on my phone, and the flash, and took a snap through the hole:

There's a rivet at the bottom I'd drilled out previously, dropped onto what looks like yellow sludge. Not knowing how much corrosion this water might have caused, I had not choice but to cut out the beam:

Sludge in the ends too:

It looks like gold dust, but it seems to be very fine clay, which I guess got in there the same way as the water - through the places where the rivets are - that is the only possibility.

Anyone with a catamaran with a beam that is embedded into the hulls and which has any rivets in it would do well to drill a small hole in the bottom to check for water inside! Bad design! I think embedded beams can be OK - it is surely a strong connection, but if the beam is not entirely water-tight, there'll be trouble, and rivets can't be relied upon to remain water-tight.

The good news is the extent of the corrosion in the beam - it's not enough to require a new beam, but enough that it was essential that it wasn't allowed to progress further. A bonus is that I will now be able to tweak my plans for the new arrangement with a seagull striker, because I can now easily transport my beam to the welding shop and have the new fittings welded on instead of clamped on as I'd planned previously.

Here's a beam stump ready for laminating over:

A piece of ply was used to fill the space where I've removed the foam, and the whole lot glassed over with biax. The ply knees and other structure I built into the hull to support the beam can be used to give support to the aluminium pads I've have made to provide support to the new beam.

Here's the modified plan:

Off to the welders!

Some arrangements for fitting a storm jib.

I am going to a lot of trouble to give the boat a storm jib, mounted on a removable inner forestay. I think a storm jib is a sail that is often left in the bag on a boat - few people use them. But I have sailed all the way from the Canaries - Madeira - the Azores - UK under storm jib for 95% of the trip. I had wind on the nose varying from F6-8 all the way. I'd gone as far west as the Azores to pick up the south-westerlies to get me back to the UK, and did indeed set off from there with a fair wind, but it only lasted 12 hours. Then I was back to the storm jib and either double or triple-reefed main all the way to Start Point, all of it close-hauled.

I had an inner forestay on that boat (a plywood 32' monohull) which I'd fitted specifically for taking a storm jib but I did experiment with hanging the storm jib from the main forestay, to see how it might work. I could go to windward alright, but at only 2-3 knots. Hanging the storm jib from the inner forestay, so that it just about overlapped the reefed main, I got 6-7 knots. For two weeks crashing through waves all the way from the Azores, I was very glad to have that sail and that rig.

Besides allowing me to continue sailing at a reasonable speed in strong winds, the storm jib also allows me to sail slowly in lighter winds - to await daylight before entering a new harbour, to catch up on some rest, or to go fishing. I have already fitted a catwalk between the front aluminium beam and the front of the saloon, but I need bobstays to counteract the upward pull of the inner forestay.

The bobstay fittings that were previously used for the front beam were no use - they were fitted too high for one thing, making the angle too shallow. And the support inside the hull was inadequate too:

In the bows of the boat, a floor is glassed in about 20 cm above the water line. A block of wood has been glassed onto the wall of the hull at floor level to take the load of the old bobstays. I don't think this is strong enough, or low enough. The yellow area behind the text in the image above is a hole I dug through the floor and through the foam that fills that area to place a new load bearing construction.

I used a grinder to cut through the floor - which was surprisingly substantial - an Airex sandwich. And then a wire brush on a drill to pulverise the foam underneath with a hose from a vacuum sucking away the dust.

It would be crazy to do such work in such a confined space without the benefit of an air-fed mask:

These masks sell for £6-700! I was lucky to find one at the local dump, and acquired it for £3. It had no battery and the exhaust valve was ruined. Replacement parts are also very expensive, so I had to adapt it a little. A 6v battery charger wired in to the motor runs the fan, and a vinyl glove with the ends of the fingers cut off works like the valve. An old filter cut down and glued to a flexible pipe allows me to work with either filters or a tube leading to a supply of fresh air. The fan is a bit noisy, and I feel pretty constricted working in it, but I get fresh air to my face and so don't have to breathe either fibreglass dust or epoxy fumes. Ear defenders and a set of plastic overalls for epoxying add to the discomfort. I'm also working in a space where I can just about sit up... but that's enough wingeing! Back to work!

I glued a pad of plywood to the surface of the inner skin of glass with epoxy and fillers. I then glued in a plywood floor, and plywood to the front and back of the hole. I filleted the joins, and glassed it all together with epoxy and biaxial glass. From the outside, I ground away the outer skin, and the foam underneath, and filled the hollow with many layers of epoxy and glass:

In this way, there is no foam where I will attach the bobstay fittings - just solid glass and epoxy. And the load is spread between the outer skin and the inner skin, and via the plywood construction to the inner skin of the other side of the hull. I will use a stainless steel backing plate to spread the load of the nuts of the fitting evenly.

I think this structure is so strong it would be suitable for attaching my anchor bridle too, which I'll bear in mind when choosing the fitting I'll use here.

Phew - several days work grinding and epoxying to create a thing probably no-one will ever see or appreciate, except you reader! Thanks for your attention!